wanted 3 phase motor to suit myford series 7 lathe

WANTED, 3-PHASE MOTOR TO SUIT MYFORD SERIES 7 LATHE.

I have an excellent single phase (230 volt) Motor 550 watts (2/3 h.p.). Removed from Myford Super 7 lathe. See photos. Made by EMAC of Scotland. Complete with capacitor & shaft key. Good clean condition, tests OK. With good resilient mounting rings to fit your existing motor cradle. I will sell it for £70 or may part-exchange it for a comparable 3-phase resiliently-mounted motor. Must be dual voltage -phase 3/4 to 1-h.p. motor in good working condition. Read More

WANTED, 3-PHASE MOTOR for MYFORD series 7 lathe.

I am looking for a 3-phase resiliently-mounted motor to suit my Myford Super 7. Must be dual voltage -phase 3/4 to 1-h.p. motor in good working condition. I have an excellent single phase (230 volt) Motor 550 watts (2/3 h.p.) to suit a Myford lathe. See photos. Made by EMAC of Scotland. Complete with capacitor & shaft key. Good clean condition, tests OK. With good resilient mounting rings to fit your existing motor cradle. I will sell it for £70 or consider a comparable part-exchange. Read More

ELECTRIC MOTOR TO SUIT MYFORD LATHE

Single phase (230 volt) Motor 550 watts (2/3 h.p.). Removed from my Myford Super 7 lathe when converting to 3-phase system. Made by EMAC of Scotland. Complete with capacitor and shaft key. Good clean condition, tests OK. With good resilient (rubber) mounting rings to fit your existing motor cradle. Postage £10 or collect from close to M6 Jn 27. Read More

ELECTRIC MOTOR TO SUIT MYFORD OR SIMILAR LATHE.

Single phase (230 volt) Motor 550 watts (2/3 h.p.). Removed from my Myford Super 7 lathe when converting to 3-phase system. Made by EMAC of Scotland. Complete with capacitor & shaft key. Good clean condition, tests OK. With good resilient mounting rings to fit your existing motor cradle. Post free or collect from close to M6 Jn 27 and save £5.. Possible £25 part-ex for similar -phase 1-h.p. motor in good condition (callers only). Read More

ELECTRIC MOTOR TO SUIT MYFORD OR SIMILAR LATHE.

Single phase (230 volt) Motor 550 watts (2/3 h.p.). Removed from my Myford Super 7 lathe when converting to 3-phase system. Made by EMAC of Scotland. Complete with capacitor & shaft key. Good clean condition, tests OK. With good resilient mounting rings to fit your existing motor cradle. Post free or collect from close to M6 Jn 27 and save £5.. Possible £25 part-ex for similar -phase motor in good condition (callers only). Read More

New & Unused 230 volt motor for MYFORD Series 7 lathe

I have for sale a new 230 volt, 550 watts (3/4 h.p.) rpm resiliently-mounted motor bought (in error) for my lathe rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Runs almost silently. Price includes carriage to all except remote areas, for which I can quote the extra price on receipt of your postcode. I also want a sound 230-volt Myford compatible coolant pump priced at around £50. Read More

SAVE £50. New 230 volt motor for MYFORD Series 7 lathe.

I have for sale a new 230 volt, 550 watts (3/4 h.p.) rpm resiliently-mounted motor bought (in error) for my lathe rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Runs almost silently. My price includes carriage to all except remote areas, for which I can quote the extra price on receipt of your postcode.. I need a similar 3-phase motor for my lathe, which has an inverter drive, and would consider a part-exchange on the above or a direct swap if your motor 3-phase motor is in new condition.. I also need a sound 230-volt Myford compatible coolant pump with a stem length of 180 mm. priced at around £50. Read More

SAVE £50. New 230 volt motor for MYFORD Series 7 lathe.

I have for sale a new 230 volt, 550 watts (3/4 h.p.) rpm resiliently-mounted motor bought (in error) for my lathe rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Runs almost silently. My price includes carriage to all except remote areas, for which I can quote the extra price on receipt of your postcode.. I also want a sound 230-volt Myford compatible coolant pump with a stem length of 180 mm. priced at around £50. Read More

REDUCED!MYFORD SERIES 7 LATHE SPARES.

Picture 1) A square control panel to smarten up your industrial cabinet, perhaps for imminent sale. Mint condition, £15.. Picture 2) One of several "Santon" reversing switches as fitted to the vast majority of early Series 7 & 10 lathes. Unlike the similar Dewhurst switch, you don't need the expensive mounting bracket, (about £35). Suitable for 1-phase (240 volts) and 3-phase (440 volts), price is £25. For an extra £5, there is a versatile enclosure (red) that can be easily fitted to your lathe cabinet (inside or out) or to any convenient flat surface... Picture 3) This shows the Santon switch outside its adaptable enclosure.. Picture 4) A new pair of Tufnol tumbler gears for ML7R & Super 7 lathes, Myford ref A teeth) & A teeth), price £30.. Picture 5). Two switched fuseboxes, suitable for three- or single-phase isolation. Three-phase, containing 3 rewirable fuses, £15, and single-phase with one fuse, £10.. Picture 6) Internal views of the above isolators. Please collect if possible. Tell me what you want & I will give you a firm price for carriage.Costs will be kept to a minimum, (usually under £5), but depending on your postcode and parcel weight. Read More

CHEAP MYFORD SERIES 7 LATHE SPARES.

Picture 1) A square control panel to smarten up your industrial cabinet, perhaps for imminent sale. Mint condition, £15.. Picture 2) One of several "Santon" reversing switches as fitted to the vast majority of early Series 7 & 10 lathes. Unlike the similar Dewhurst switch, you don't need the expensive mounting bracket, (about £35). Suitable for 1-phase (240 volts) and 3-phase (440 volts), price is £25. For an extra £5, there is a versatile enclosure (red) that can be easily fitted to your lathe cabinet (inside or out) or to any convenient flat surface... Picture 3) This shows the Santon switch outside its adaptable enclosure.. Picture 4) A NEW PAIR of Tufnol tumbler gears for ML7R & Super 7 lathes, Myford ref A teeth) & A teeth). If you strip your existing Tufnol gears you will have no drive to your gearbox and leadscrew until you can get replacements. Myford price for the 28 T is £, and their 30T gear is out of stock. My price for both is £ post free.. Picture 5). Two switched fuseboxes, suitable for three- or single-phase isolation. Three-phase, containing 3 rewirable fuses, £15, and single-phase with one fuse, £10.. Picture 6) Internal views of the above isolators. Please collect if possible. Tell me what you want & I will give you a firm price. Carriage cost will be kept to a minimum, (usually under £5), depending on your postcode and parcel weight. Read More

SAVE £50. New 230 volt motor for MYFORD Super 7 lathe.

I have for sale a new 230 volt, 550 watts (3/4 h.p.) rpm resiliently-mounted motor bought (in error) for my lathe rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Runs almost silently on test. My price includes carriage to all except remote areas, for which I can quote the extra price on receipt of your postcode.. I need a similar 3-phase motor for my lathe, which has an inverter drive, and would consider a part-exchange on the above or a direct swap if your motor 3-phase motor is in new condition.. I also need a sound 230-volt Myford compatible coolant pump with a stem length of 180 mm. priced at around £50. Read More

LOOK AT THIS ! MYFORD SERIES 7 LATHE SPARES.

Picture 1) A square control panel to smarten up your industrial cabinet, perhaps for imminent sale. Mint condition. £22.. Picture 2) One of several "Santon" reversing switches as fitted to the vast majority of early Series 7 & 10 lathes. Unlike the similar Dewhurst switch, you don't need the expensive mounting bracket, (about £35).. The 1-phase switch (240 volts) is £30, and the 3-phase (440 volts) is £35. For an extra £5, there is a versatile enclosure (red) that can be easily fitted to your lathe cabinet (inside or out) or to any convenient flat surface... Picture 3) This shows the Santon switch outside its adaptable enclosure.. Picture 4) A new pair of Tufnol tumbler gears for ML7R & Super 7 lathes, Myford ref A teeth) & A teeth). £30 post free.. Picture 5). Two switched fuseboxes, suitable for three- or single-phase isolation. Three-phase, containing 3 rewirable fuses, £17, and single-phase with one fuse, £12.. Picture 6) Internal views of the above isolators.. Picture 7) Two types of emergency lock-off stop buttons. State your preference. £ 10 each.. Please collect if possible. Carriage costs will be kept to a minimum, depending on your postcode and parcel weight. Tell me what you want & I will give you a firm price. Read More

LOOK AT THIS ! MYFORD SERIES 7 LATHE SPARES.

Picture 1) A square control panel to smarten up your industrial cabinet, perhaps for imminent sale. Mint condition. £22.. Picture 2) One of several "Santon" reversing switches as fitted to the vast majority of early Series 7 & 10 lathes. Unlike the similar Dewhurst switch, you don't need the expensive mounting bracket, (about £35).. The 1-phase switch (240 volts) is £30, and the 3-phase (440 volts) is £35. For an extra £5, there is a versatile enclosure (red) that can be easily fitted to your lathe cabinet (inside or out) or to any convenient flat surface... Picture 3) This shows the Santon switch outside its adaptable enclosure.. Picture 4) A new pair of Tufnol tumbler gears for ML7R & Super 7 lathes, Myford ref A teeth) & A teeth). £30 post free.. Picture 5). Two switched fuseboxes, suitable for three- or single-phase isolation. Three-phase, containing 3 rewirable fuses, £17, and single-phase with one fuse, £12.. Picture 6) Internal views of the above isolators.. Picture 7) Two types of emergency lock-off stop buttons. State your preference. £ 10 each. SOLD SOLD SOLD.. Please collect if possible. Carriage costs will be kept to a minimum, depending on your postcode and parcel weight. Tell me what you want & I will give you a firm price. Read More

wanted grayson lathe or myford 7

hi im after any grayson lathe parts or a grayson lathe that can be a donar lathe or myford 7 parts,must be cheepish and im willing to arrange a courier if too far for me to travel thanks Read More

WANTED - ELECTRIC MOTOR, 3-PHASE, UP TO 750 Watts. (1 H.P)

Wanted to power my Myford lathe. Cash waiting for a good sound motor,ideally with resilient mounting. must be guaranteed in full working order. Wigan area. Have British volt motor for possible part-ex. Ready cash for the right one. Read More

WANTED - SMALL ELECTRIC MOTOR, 3-PHASE, UP TO 750 W. (1 H.P)

Wanted to power my Myford lathe. Cash waiting for a good sound motor,ideally with resilient mounting. must be guaranteed in full working order. Wigan area. Ready cash for the right one. Read More

WANTED, 3-phase motor, or exchange for my 230 volt motor.

If you have a 3-phase motor to suit a Myford Series 7 lathe & want to sell it or swap it for a single-phase one, read on. It will ideally be resiliently-mounted, & similar in outward appearance to my photos. It MUST be dual voltage -phase, 3/4 to 1-h.p., in good working condition & of good appearance. Please supply photos & shaft details.. I also want a sound 230-volt Myford compatible coolant pump priced at around £50.. I have for sale (or exchange) a new 230 volt, 550 watts (3/4 h.p.) rpm motor bought (in error) for my Super 7 rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Tests OK. Price £175. If your motor is sound but scruffy, we can perhaps negotiate a deal. The buyer must collect or pay carriage, estimated as £12, but I can quote a fixed price on receipt of your postcode. Read More

WANTED, 3-phase motor, or part-ex for my 230 volt motor.

I am looking for a 3-phase resiliently-mounted motor to suit my Myford Super 7. MUST be dual voltage -phase 3/4 to 1-h.p. motor in good working condition. I have an excellent 230 volt, 550 watts (2/3 h.p.) motor to suit a Myford lathe. See photos. Made by EMAC of Scotland. Complete with capacitor & shaft key. Good clean condition, tests OK. With good resilient mounting rings to fit your existing motor cradle. I will sell it for £70 or consider part-exchange. I also have a 1/4h.p. 230 volt motor to suit an ML10 or ML7 lathe at £40. Buyer to collect or pay carriage. Read More

DIGITAL PHASE CONVERTORS X 3 - GOOD CONDITION - 240V INPUT- 415V OUTPUT - LATHE, MILLING, MOTOR

3 X DIGITAL PHASE CONVERTORS - 240V - 415V - FULLY ADJUSTABLE IDEAL FOR LATHES, MILLING MACHINES, PILAR DRILLS, INDUSTRIAL MOTORS. GOOD CONDITIN, HYUNDAI, FENNER AND DIRECT DRIVES - USED - SELLING AS JOB LOT O.N.O Ad ID: Delivery Service Consumer Credit

WANTED - MYFORD LATHE ACCESSORIES

I am looking for Myford series 7 lathe accessories. May consider complete lathe and workshop contents if available. Quick decision, cash waiting. Preferred area Lancs / Yorks / Cheshire. Please state what is on offer and price region. Read More

Myford 7 Lathe

Light use only. Box of quick changers, vertical slide, oiler and other bits Very good condition for age. Ad ID:

WANTED - MYFORD LATHE &/or ACCESSORIES

I am a retired (& bored) mechanical engineer looking for a project, ideally an unwanted Myford Series 7 lathe &/or suitable accessories. I will pay you a visit & buy on the spot if you have what I need. Some of the items I want are shown in the photo. I would consider a job lot of engineering items. Preferred collection area Lancs / Yorks / Cheshire & possibly north Wales. Please state what is on offer & price region. Read More

WANTED - MYFORD LATHE &/or ACCESSORIES

I am a retired mechanical engineer looking for a project, ideally an unwanted Myford Series 7 lathe &/or suitable accessories. See typical pictures). I will come and look & pay cash if you have what I need. Some of the accessories I need are shown in the photo. I would consider a job lot or a garage clearance of engineering items. Preferred collection area Lancs / Yorks / Cheshire & possibly north Wales. Please state what is on offer & send photos if possible. Read More

WANTED - MYFORD LATHE &/or ACCESSORIES

I am a retired (& bored) mechanical engineer looking for a project, ideally an unwanted Myford lathe &/or suitable accessories. I will pay you a visit & buy on the spot if you have what I need. Some of the items I want are shown in the photo. I would consider a job lot of engineering items. Preferred collection area Lancs / Yorks / Cheshire & possibly north Wales. Please state what is on offer & price region. Read More

Myford Super 7 lathe

Myford Super 7 lathe. 240 volt, runs but not used for a few years, faceplate, chuck a d some turning tools included. Collection only. Read More

Contact

• Next →