reducedmyford series 7 lathe spares

REDUCED!MYFORD SERIES 7 LATHE SPARES.

Picture 1) A square control panel to smarten up your industrial cabinet, perhaps for imminent sale. Mint condition, £15.. Picture 2) One of several "Santon" reversing switches as fitted to the vast majority of early Series 7 & 10 lathes. Unlike the similar Dewhurst switch, you don't need the expensive mounting bracket, (about £35). Suitable for 1-phase (240 volts) and 3-phase (440 volts), price is £25. For an extra £5, there is a versatile enclosure (red) that can be easily fitted to your lathe cabinet (inside or out) or to any convenient flat surface... Picture 3) This shows the Santon switch outside its adaptable enclosure.. Picture 4) A new pair of Tufnol tumbler gears for ML7R & Super 7 lathes, Myford ref A teeth) & A teeth), price £30.. Picture 5). Two switched fuseboxes, suitable for three- or single-phase isolation. Three-phase, containing 3 rewirable fuses, £15, and single-phase with one fuse, £10.. Picture 6) Internal views of the above isolators. Please collect if possible. Tell me what you want & I will give you a firm price for carriage.Costs will be kept to a minimum, (usually under £5), but depending on your postcode and parcel weight. Read More

CHEAP MYFORD SERIES 7 LATHE SPARES.

Picture 1) A square control panel to smarten up your industrial cabinet, perhaps for imminent sale. Mint condition, £15.. Picture 2) One of several "Santon" reversing switches as fitted to the vast majority of early Series 7 & 10 lathes. Unlike the similar Dewhurst switch, you don't need the expensive mounting bracket, (about £35). Suitable for 1-phase (240 volts) and 3-phase (440 volts), price is £25. For an extra £5, there is a versatile enclosure (red) that can be easily fitted to your lathe cabinet (inside or out) or to any convenient flat surface... Picture 3) This shows the Santon switch outside its adaptable enclosure.. Picture 4) A NEW PAIR of Tufnol tumbler gears for ML7R & Super 7 lathes, Myford ref A teeth) & A teeth). If you strip your existing Tufnol gears you will have no drive to your gearbox and leadscrew until you can get replacements. Myford price for the 28 T is £, and their 30T gear is out of stock. My price for both is £ post free.. Picture 5). Two switched fuseboxes, suitable for three- or single-phase isolation. Three-phase, containing 3 rewirable fuses, £15, and single-phase with one fuse, £10.. Picture 6) Internal views of the above isolators. Please collect if possible. Tell me what you want & I will give you a firm price. Carriage cost will be kept to a minimum, (usually under £5), depending on your postcode and parcel weight. Read More

LOOK AT THIS ! MYFORD SERIES 7 LATHE SPARES.

Picture 1) A square control panel to smarten up your industrial cabinet, perhaps for imminent sale. Mint condition. £22.. Picture 2) One of several "Santon" reversing switches as fitted to the vast majority of early Series 7 & 10 lathes. Unlike the similar Dewhurst switch, you don't need the expensive mounting bracket, (about £35).. The 1-phase switch (240 volts) is £30, and the 3-phase (440 volts) is £35. For an extra £5, there is a versatile enclosure (red) that can be easily fitted to your lathe cabinet (inside or out) or to any convenient flat surface... Picture 3) This shows the Santon switch outside its adaptable enclosure.. Picture 4) A new pair of Tufnol tumbler gears for ML7R & Super 7 lathes, Myford ref A teeth) & A teeth). £30 post free.. Picture 5). Two switched fuseboxes, suitable for three- or single-phase isolation. Three-phase, containing 3 rewirable fuses, £17, and single-phase with one fuse, £12.. Picture 6) Internal views of the above isolators.. Picture 7) Two types of emergency lock-off stop buttons. State your preference. £ 10 each.. Please collect if possible. Carriage costs will be kept to a minimum, depending on your postcode and parcel weight. Tell me what you want & I will give you a firm price. Read More

LOOK AT THIS ! MYFORD SERIES 7 LATHE SPARES.

Picture 1) A square control panel to smarten up your industrial cabinet, perhaps for imminent sale. Mint condition. £22.. Picture 2) One of several "Santon" reversing switches as fitted to the vast majority of early Series 7 & 10 lathes. Unlike the similar Dewhurst switch, you don't need the expensive mounting bracket, (about £35).. The 1-phase switch (240 volts) is £30, and the 3-phase (440 volts) is £35. For an extra £5, there is a versatile enclosure (red) that can be easily fitted to your lathe cabinet (inside or out) or to any convenient flat surface... Picture 3) This shows the Santon switch outside its adaptable enclosure.. Picture 4) A new pair of Tufnol tumbler gears for ML7R & Super 7 lathes, Myford ref A teeth) & A teeth). £30 post free.. Picture 5). Two switched fuseboxes, suitable for three- or single-phase isolation. Three-phase, containing 3 rewirable fuses, £17, and single-phase with one fuse, £12.. Picture 6) Internal views of the above isolators.. Picture 7) Two types of emergency lock-off stop buttons. State your preference. £ 10 each. SOLD SOLD SOLD.. Please collect if possible. Carriage costs will be kept to a minimum, depending on your postcode and parcel weight. Tell me what you want & I will give you a firm price. Read More

WANTED, 3-PHASE MOTOR for MYFORD series 7 lathe.

I am looking for a 3-phase resiliently-mounted motor to suit my Myford Super 7. Must be dual voltage -phase 3/4 to 1-h.p. motor in good working condition. I have an excellent single phase (230 volt) Motor 550 watts (2/3 h.p.) to suit a Myford lathe. See photos. Made by EMAC of Scotland. Complete with capacitor & shaft key. Good clean condition, tests OK. With good resilient mounting rings to fit your existing motor cradle. I will sell it for £70 or consider a comparable part-exchange. Read More

New & Unused 230 volt motor for MYFORD Series 7 lathe

I have for sale a new 230 volt, 550 watts (3/4 h.p.) rpm resiliently-mounted motor bought (in error) for my lathe rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Runs almost silently. Price includes carriage to all except remote areas, for which I can quote the extra price on receipt of your postcode. I also want a sound 230-volt Myford compatible coolant pump priced at around £50. Read More

WANTED, 3-PHASE MOTOR TO SUIT MYFORD SERIES 7 LATHE.

I have an excellent single phase (230 volt) Motor 550 watts (2/3 h.p.). Removed from Myford Super 7 lathe. See photos. Made by EMAC of Scotland. Complete with capacitor & shaft key. Good clean condition, tests OK. With good resilient mounting rings to fit your existing motor cradle. I will sell it for £70 or may part-exchange it for a comparable 3-phase resiliently-mounted motor. Must be dual voltage -phase 3/4 to 1-h.p. motor in good working condition. Read More

SAVE £50. New 230 volt motor for MYFORD Series 7 lathe.

I have for sale a new 230 volt, 550 watts (3/4 h.p.) rpm resiliently-mounted motor bought (in error) for my lathe rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Runs almost silently. My price includes carriage to all except remote areas, for which I can quote the extra price on receipt of your postcode.. I need a similar 3-phase motor for my lathe, which has an inverter drive, and would consider a part-exchange on the above or a direct swap if your motor 3-phase motor is in new condition.. I also need a sound 230-volt Myford compatible coolant pump with a stem length of 180 mm. priced at around £50. Read More

SAVE £50. New 230 volt motor for MYFORD Series 7 lathe.

I have for sale a new 230 volt, 550 watts (3/4 h.p.) rpm resiliently-mounted motor bought (in error) for my lathe rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Runs almost silently. My price includes carriage to all except remote areas, for which I can quote the extra price on receipt of your postcode.. I also want a sound 230-volt Myford compatible coolant pump with a stem length of 180 mm. priced at around £50. Read More

lathe spares

12 inch faceplate Colchester early machine Read More

lathe spares

12 inch faceplate Harrison early machine Read More

metal lathe wanted for spares.

Old metal lathe wanted for spares. Anything considered. Can collect at your convenience. Thank You. Read More

Pultra series lathe

Condition not too important providing it is complete. I have a suitable electric motor. Read More

Myford 7 Lathe

Light use only. Box of quick changers, vertical slide, oiler and other bits Very good condition for age. Ad ID:

MFORD SUPER 7 LATHE

This lathe is in excellent condition. It was a gift from Father to son for getting his degree. I bought it from the son, now aged 65. and in excellent condition throughout. (have a F.T.C Dept 63 from C & G) and practised toolmaking since . All the extras you see on the photos will be included, together with a comprehensive hand book, (new) You are most welcomed to come along to Abergele and see the Lathe. I include FREE delivery using a pallet service included in the price. I have 20 photos on Photobox and will post the link address as soon as possible. The lathe has 3 and 4 jaw chucks, a face-plate and Striking plate. The original testing bar is included together with it. A full set of change wheels which includes the metric 21 tooth gear. It is a single phase motor.. Read More

Myford Super 7 lathe

Myford Super 7 lathe. 240 volt, runs but not used for a few years, faceplate, chuck a d some turning tools included. Collection only. Read More

MYFORD SUPER 7 CENTRE LATHE

We have For Sale a MYFORD SUPER 7 CENTRE LATHE Complete with 3 JAW 4 JAW FACE PLATE AND NUMEROUS ACCESSORIES. COLLECTION ONLY PLEASE. Read More

MYFORD SUPER 7 CENTRE LATHE

We have For Sale a MYFORD SUPER 7 CENTRE LATHE Complete with 3 JAW 4 JAW FACE PLATE AND NUMEROUS ACCESSORIES. COLLECTION ONLY PLEASE. The Lathe separates from the base and the measurements are BASE inches wide, x 34.5 inches high x 15.5 inches deep. The LATHE itself measures 44 inches wide, 22 inches high x 18 inches deep. Read More

LATHE clarke CL500M Professional Metal Lathe Mill/Drill

6-7 year old Clarke lathe Mill/Drill. Never been used. It has been kept in a dry shed for the past 4-5 years all the accessories are still wrapped. there is a very small amount of tarnishing on the bare steel but nothing that a little TLC can't quickly get sorted. the full description is pictured from a recent catalogue. THE PICTURED FLOOR STAND IS NOT PART OF THIS SALE. to the best of my knowledge all the belts and accessories are present and a part of this sale This is an extremely heavy piece of machinery even when the mill/drill is detached. Delivery is possible but that will have to be a separate negotiation accepted payment of PayPal C.O.D. C.O.C Read More

myford Steel turning Lathe, lathe on original stand...

myford Steel turning Lathe, lathe on original stand manufactured approx 35 years is in good working order.3 jaw chuck andface plate £, Llanelli, .

LATHE clarke CL500M Professional Metal Lathe Mill/Drill

6-7 year old Clarke lathe Mill/Drill. Never been used. It has been kept in a dry shed for the past 4-5 years all the accessories are still wrapped. there is a very small amount of tarnishing on the bare steel but nothing that a little TLC can't quickly get sorted. the full description is pictured from a recent catalogue. THE PICTURED FLOOR STAND IS NOT PART OF THIS SALE. to the best of my knowledge all the belts and accessories are present and a part of this sale This is an extremely heavy piece of machinery even when the mill/drill is detached. Delivery is possible but that will have to be a separate negotiation accepted payment of PayPal C.O.D. C.O.C. Read More

Large High Quality Industrial Metal Lathe / Wood Lathe

industrial lathe, can be used for both metal and wood.. very heavy cast iron legs etc.. steal top.. overall approximately 150kg Perfect working order, Clarke Motor 1.5hp, very smooth operation Read More

Myford Lathe ML10 (Metal lathe) in Guildford

Myford ML10, used condition, forward and backwards motor however the motor is underpowered for the machine. Has a new lead screw clutch fitted. Comes with some change wheels (see photo) Face plate. 3 jaw chuck. Lathe Manual Serial No.

wanted grayson lathe or myford 7

hi im after any grayson lathe parts or a grayson lathe that can be a donar lathe or myford 7 parts,must be cheepish and im willing to arrange a courier if too far for me to travel thanks Read More

nova g3 lathe chuck 3/4x16tpi for wood lathe brand new boxed

for sale a brand new boxed nova g3 chuck for wood lathe 3/4x16tpi all complete with chuck body a set of standard nova jaws. faceplate and worm chuck both fit in the chuck it is all there with manual and chuck key you can see all the pictures clearly on you can collect or have it posted at cost via hermes

Contact

• Next →