iris 50 hand bearing compass new for

  Iris 50 Hand Bearing Compass New For

New iris 50 hand bearing compass in yellow, Uk buyers only please.  

Plastimo Iris 50 hand bearing compass

Blue Plastimo Iris 50 hand bearing compass, complete with plastic storage pouch. Little used & in excellent condition. Ad ID: Delivery Service Consumer Credit

  Plastimo Iris 50 Hand Bearing Compass

Second hand great condition.please note no returns.

Plastimo Iris 50 hand bearing compass

Blue Plastimo Iris 50 hand bearing compass, complete with plastic storage pouch. Little used & in excellent condition. Read More

Plastimo Iris 100 Hand Bearing Compass

Plastimo Iris 100 Hand Bearing compass. 295g. Gimballed, even works upside down. Soft rubber casing and floats.

  Plastimo Iris 50 Sailing Compass - Hand

Here I am selling a Plastimo Iris 50 Sailing Compass. It is used, but in excellent condition and comes with a lanyard, pouch and instructions. It can be used day or night! Just shine a torch on it for a few seconds and the dial glows in the dark - brilliant. LOW START NO RESERVE PLEASE SEE MY OTHER SAILING AND YACHTING ITEMS LISTED FOR SALE THIS WEEK

Iris 50 compass

Iris 50 compass as new Ad ID:

Hand bearing compass.

Plastimo Iris 50 hand bearing compass on lanyard. In good condition, very clear sight. Ad ID: Delivery Service Consumer Credit

Marine Hand Bearing Compass

Marine Hand Bearing Compass complete with case. Stopped sailing so no longer required. Ad ID: Delivery Service Consumer Credit

Carac Hand Bearing Compass

Compass as new still with instructions and spare bulb. Fully working Bulb needs 2AA batteries. No corrosion all in excellent condition. As new Read More

Plastimo Hand Bearing Compass in Lostwithiel

Plastimo Hand Bearing Compass. Gimballed. Even works upside down. 295g. Soft rubber casing and floats.

Ww2 hand bearing compass in Milton Keynes

Air force. Hand held compass. Please see pictures for condition. I dont have any history for this item. Swap or militaria taken in p.x. Please text or email. I will get back to you. Thanks

Pocket Hand Bearing Compass in Hayling Island

Surplus to requirements, this is a very compact and light weight hand bearing compass for boats/trekking/orienteering etc; it is in as new condition. It has lovely clear markings every 2 degrees and is well damped. It can be kept in a pocket or hung around your neck on its lanyard. It is made by Yachting Electrical Services of Reading, and the sides are fully enclosed in soft rubber so it will survive being dropped! At £15 it is much cheaper than the Plastimo Iris 50. Buyer collects or I could post it at cost, currently £2.80 at Post Office rates..

Vintage Sestrel Hand bearing compass in mint condition

Sestrel hand bearing with perspex top and detachable handle in an immaculate condition with no scratches. Comes with black handle and kept securely in a samsonite camera case. Been in the family since the late 's Ad ID: Delivery Service Consumer Credit

Sestrel Hand Bearing Compass - Naval, Marine, Yachting, Sailing, Navigation, Brass, Antique, Vintage

Henry Browne & Son Ltd, Barking & London, 'Sestrel' Trade Mark, No. /B, Made in England. This compass is considered the finest of its type ever designed. The bowl is cast bronze. The optical glass prism allows the user to sight at the object and at the same time see the compass bearing in his field of view, and magnifies the card for easy use. An iridium chip beneath the card lights it for night time use. The compass is mounted on a solid teak handle with card-holder to make notations. COMES COMPLETE WITH (The compass sits in a) holder that can be fixed to bulkhead, mast, etc - as appropriate. Henry Browne & Son made only the highest quality marine navigation gear under the "Sestrel" trade mark and were purchased by Lilley & Gillie around when the marine industry was being consolidated. The Sestrel operations were sold more than once. SIRS Co., is manufacturing this compass ('Sestrel') today under the "Radiant" name (hand-held NATO coded compass ) and will sell you one for £895. I am selling my vintage example for £225. Collection from Maiden Newton DT2 Ad ID: Delivery Services Consumer Credit

Bronze Cutless Bearing Housing for 25mm diam Bearing & Shaft, also Inboard Bearing Housing Available

This is a used cutless bearing housing to take a 25mm diameter bearing and propellor-shaft. It is made of cast bronze, and takes a 50mm long bearing, which was rather short for our 1 metre long prop shaft, so we have changed to a 100mm long housing and bearing, which cost over £200. It will be fine for a short prop shaft, or a situation where there is not enough room for a longer bearing housing such as inside a rudder aperture on a long-keeler. The inboard end of the casting is threaded for attaching to the stern tube, and the threads are 16 TPinch, or 6TPcm, and inch diameter on a 1.5 inch diameter tube. The two anti-twist bolt holes are at 4.3 inch, 110mm, centres. A suitable new section of bearing is available at no extra charge. Asking £65 ono I also have available the bearing housing from the inboard end of the same stern tube, with the same thread. Would sell sperately for £60 ono, or together for £110 ono. Buyer collects or I could post it at cost. Ad ID: Delivery Services Consumer Credit

Bronze Cutless Bearing Housing for 25mm diam Bearing & Shaft, also Inboard Bearing Housing Available

This is a used cutless bearing housing to take a 25mm diameter bearing and propellor-shaft. It is made of cast bronze, and takes a 50mm long bearing, which was rather short for our 1 metre long prop shaft, so we have changed to a 100mm long housing and bearing, which cost over £200. As it is the removable bearing that takes all the wear, it is is fine condition. It will be suitable for a short prop shaft, or a situation where there is not enough room for a longer bearing housing such as inside a rudder aperture on a long-keeler. The inboard end of the casting is threaded for attaching to the stern tube, and the threads are 16 TPinch, or 6 TPcm, and inch diameter on a 1.5 inch diameter tube. The two anti-twist bolt holes are at 4.3 inch, 110mm, centres. A suitable new section of bearing is available at no extra charge. Asking £65 ono I also have available the bearing housing from the inboard end of the same stern tube, with the same thread. Would sell sperately for £65 ono, or together for £120 ono. Buyer collects or I could post it at cost. Ad ID: Delivery Service Consumer Credit

Bronze Cutless Bearing Housing for 25mm diam Bearing & Shaft, also Inboard Bearing Housing Available

This is a used cutless bearing housing to take a 25mm diameter bearing and propellor-shaft. It is made of cast bronze, and takes a 50mm long bearing, which was rather short for our 1 metre long prop shaft, so we have changed to a 100mm long housing and bearing, which cost over £200. It will be fine for a short prop shaft, or a situation where there is not enough room for a longer bearing housing such as inside a rudder aperture on a long-keeler. The inboard end of the casting is threaded for attaching to the stern tube, and the threads are 16 TPinch, or 6TPcm, and inch diameter on a 1.5 inch diameter tube. The two anti-twist bolt holes are at 4.3 inch, 110mm, centres. A suitable new section of bearing is available at no extra charge. Asking £65 ono I also have available the bearing housing from the inboard end of the same stern tube, with the same thread. Would sell sperately for £65 ono, or together for £120 ono. Buyer collects or I could post it at cost. Ad ID: Delivery Services Consumer Credit

Boer war compass,military compass,brass compass,ww1 compass,militaria,vintage compass

Boer war military compass owned for many year arrow stamp and maker please see pictures there is a crack on the small outer glass but is a genuine boer war/ww1 item.please call . Ad ID: Delivery Service Consumer Credit

NEW Tri Spinner Fidget Metal Finger Stress Hand Bearing

Quantity: Change country: -Select- Andorra Argentina Australia Belarus Belgium Bosnia and Herzegovina Brazil Bulgaria Canada Croatia, Republic of Cyprus Czech Republic Denmark Estonia Finland France Gibraltar Greece Guernsey Hungary Iceland Ireland Japan Jersey Korea, South Latvia Liechtenstein Lithuania Luxembourg Macedonia Malta Mexico Moldova Monaco Montenegro Netherlands New Zealand Norway Poland Portugal Romania Russian Federation San Marino Serbia Slovakia Slovenia Sweden Ukraine United Kingdom United States Vatican City State There are 90 items available. Please enter a number less than or equal to 90. Select a valid country. Postcode: Please enter a valid postcode. Please enter up to 7 characters for the postcode

Bronze Cutless Bearing Housing for 25mm diam Bearing & Shaft

This is a used cutless bearing housing to take a 25mm diameter bearing and propellor-shaft. It is made of cast bronze, and takes a 50mm long bearing, which was rather short for our 1 metre long prop shaft, so we have changed to a 100mm long housing and bearing. It will be fine for a short prop shaft, or a situation where there is not enough room for a longer bearing housing such as inside a rudder aperture on a long-keeler. (The brass tube from the old bearing is still in situ.) The inboard end of the casting is threaded for attaching to the stern tube, and the threads are 16 TPinch, or 6TPcm, and inch diameter on a 1.5 inch diameter tube. The two anti-twist bolt holes are at 4.3 inch, 110mm, centres. A suitable new section of bearing is available at no extra charge. (The new 100 mm housing cost nearly £200!) Asking £65 ono Buyer collects or I could post it at cost.

Bronze Cutless Bearing Housing for 25mm diam Bearing & Shaft

This is a used cutless bearing housing to take a 25mm diameter bearing and propellor-shaft. It is made of cast bronze, and takes a 50mm long bearing, which was rather short for our 1 metre long prop shaft, so we have changed to a 100mm long housing and bearing. It will be fine for a short prop shaft, or a situation where there is not enough room for a longer bearing housing such as inside a rudder aperture on a long-keeler. The inboard end of the casting is threaded for attaching to the stern tube, and the threads are 16 TPinch, or 6TPcm, and inch diameter on a 1.5 inch diameter tube. The two anti-twist bolt holes are at 4.3 inch, 110mm, centres. A suitable new section of bearing is available at no extra charge. Asking £65 ono Buyer collects or I could post it at cost.

Bronze Cutless Bearing Housing for 25mm diam Bearing & Shaft

This is a used cutless bearing housing to take a 25mm diameter bearing and propellor-shaft. It is made of cast bronze, and takes a 50mm long bearing, which was rather short for our 1 metre long prop shaft, so we have changed to a 100mm long housing and bearing. It will be fine for a short prop shaft, or a situation where there is not enough room for a longer bearing housing such as inside a rudder aperture on a long-keeler. The inboard end of the casting is threaded for attaching to the stern tube, and the threads are 16 TPinch, or 6TPcm, and inch diameter on a 1.5 inch diameter tube. The two anti-twist bolt holes are at 4.3 inch, 110mm, centres. A suitable new section of bearing is available at no extra charge. Asking £65 ono Buyer collects or I could post it at cost. Read More

Sealed High Speed Bearing Snowblower Bearing For Ariens &

Quantity: Change country: -Select- Australia Austria Bahrain Belgium Brazil Bulgaria Canada Chile Colombia Costa Rica Croatia, Republic of Cyprus Czech Republic Denmark Dominican Republic El Salvador Estonia Finland France Germany Greece Guatemala Honduras Hong Kong Hungary Indonesia Ireland Israel Italy Jamaica Japan Korea, South Kuwait Latvia Lithuania Malaysia Malta Mexico Netherlands New Zealand Norway Panama Philippines Poland Portugal Qatar Romania Russian Federation Saudi Arabia Singapore Slovakia Slovenia South Africa Spain Sweden Switzerland Taiwan Trinidad and Tobago Ukraine United Arab Emirates United Kingdom United States There are 55 items available. Please enter a number less than or equal to 55. Select a valid country. Postcode: Please enter a valid postcode. Please enter up to 7 characters for the postcode

NEW FIDGET FINGER SPINNER HAND FOCUS SPIN STEEL EDC BEARING

Quantity: Change country: -Select- Australia Austria Azerbaijan Republic Belarus Belgium Bosnia and Herzegovina Brazil Bulgaria Canada Croatia, Republic of Cyprus Czech Republic Denmark Estonia Finland France Germany Greece Guernsey Hungary Ireland Israel Italy Japan Jersey Kazakhstan Korea, South Latvia Lithuania Luxembourg Malaysia Maldives Malta Netherlands New Zealand Norway Poland Portugal Romania Russian Federation Saudi Arabia Singapore Slovakia Slovenia Spain Sweden Switzerland Thailand Turkey Ukraine United Arab Emirates United Kingdom There are 30 items available. Please enter a number less than or equal to 30. Select a valid country. Postcode: Please enter a valid postcode. Please enter up to 7 characters for the postcode

Contact

• Next →