stand for myford super 7

STAND for MYFORD SUPER 7...

STAND for MYFORD SUPER 7, or 7. Same shape as original. Call for any other details. £, Battle, .

Tailstock Barrel for Myford Super 7 in St. Austell

Item in good condition with no apparent wear visible. Buyer to pay postage.

Front Headstock Bearing for Myford Super 7 in St. Austell

Item is in unused condition as it has been kept for spares.Buyer to pay postage.

SAVE £50. New 230 volt motor for MYFORD Super 7 lathe.

I have for sale a new 230 volt, 550 watts (3/4 h.p.) rpm resiliently-mounted motor bought (in error) for my lathe rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Runs almost silently on test. My price includes carriage to all except remote areas, for which I can quote the extra price on receipt of your postcode.. I need a similar 3-phase motor for my lathe, which has an inverter drive, and would consider a part-exchange on the above or a direct swap if your motor 3-phase motor is in new condition.. I also need a sound 230-volt Myford compatible coolant pump with a stem length of 180 mm. priced at around £50. Read More

Myford Super 7 Handbook.

A spotless copy of the Super 7 handbook, usefully enhanced with a spiral binder and transparent plastic end covers, making it easier to read (Stays open at the required page) and stays cleaner in use. (New price £).. I have lots of other Myford publications to sell or swap. See pictures 2 to 8 above. All items available for sale individually or as a job lot. Please be aware that the ML7 & ML7R handbooks (Pic 2, gray & green covers) have been sold. All items sent post free. Read more

Myford Super 7 lathe

Myford Super 7 lathe. 240 volt, runs but not used for a few years, faceplate, chuck a d some turning tools included. Collection only. Read More

Wanted,Myford Super 7 Handbook

A clean copy of the Super 7 handbook (Blue Cover) wanted by Myford owner. Good price paid for the genuine article. If you prefer, I have lots of other Myford publications to swap. See below. Read More

Wanted, Myford Super 7 Handbook.

Pic. 1) Wanted. A clean copy of the Super 7 handbook (Blue Cover). A fair price paid for the genuine article. If you prefer, I have lots of other Myford publications to sell or swap, of which I offer any two in exchange for the Super 7 handbook. See pictures 2 to 9 above. All items available for sale individually or as a job lot. Please be aware that the ML7 handbook (grey cover) has been sold. Read More

MYFORD SUPER 7 CENTRE LATHE

We have For Sale a MYFORD SUPER 7 CENTRE LATHE Complete with 3 JAW 4 JAW FACE PLATE AND NUMEROUS ACCESSORIES. COLLECTION ONLY PLEASE. Read More

MYFORD SUPER 7 CENTRE LATHE

We have For Sale a MYFORD SUPER 7 CENTRE LATHE Complete with 3 JAW 4 JAW FACE PLATE AND NUMEROUS ACCESSORIES. COLLECTION ONLY PLEASE. The Lathe separates from the base and the measurements are BASE inches wide, x 34.5 inches high x 15.5 inches deep. The LATHE itself measures 44 inches wide, 22 inches high x 18 inches deep. Read More

Copy of Original Myford Super 7 Handbook.

I have for sale a mint copy of the Super 7 handbook (Blue Cover), plus lots of other Myford publications to sell or swap. See pictures 2 to 9 above. All items available for sale individually or as a job lot. Please be aware that the ML7 & ML7R handbooks (Pic 2, gray & green covers) have been sold. All items sent post free. Read more

Genuine (blue cover) Myford Super 7 PXF Handbook

Lifelong Myford fan, wanting a really clean Myford Super7 PXF handbook. Would swap for any two of the items listed below, being my collection of handbooks & literature of interest to owners of older Myford lathes. Information typically includes dimensions, weights, wiring diagrams, accessories & spares. All are in good, usable condition, although their ages vary between years. I offer the following;-. A) Myford " and 3.5" Lathes. (14 pages) Instructions on their Operation, Adjustment & the use of Accessories. (.. B) Myford ML7-R Lathe. (48 pages). Publication 572. Notes on Operation, Installation & Maintenance, also Pictorial parts List. (). This one is in particularly good (non-oily) condition. £15. C) Myford ML 10 & Speed 10 Lathes, Publication C. (6 page leaflet). Tooling & Ancillary Equipment. (.. D) Dewhurst Data Sheet QE-, Issue page leaflet). Type A Reversing Drum Switch Series SDR 52 for small motors. (Wiring diagrams & spares list). £5.. E) Copies of old Myford sales literature, spares, accessories & ancillary equipment lists for powered & non-powered cross-feed versions of the Super 7. £10 each. (please state your specific interest). All in good and mostly non-oily condition.. F) I also have information on the Myford Rodney milling attachment if this is of interest. Let me know if you want to buy the lot (at a hefty discount).. Please note that the grey ML7 handbook shown in the pictures has now been sold.. Prices include postage to UK mainland. Read More

MYFORD SUPER-7 Lathe, quick change gearbox, single...

MYFORD SUPER-7 Lathe, quick change gearbox, single phase 13amp, very little use. As new condition. £ Robertsbridge

Lathe: Myford / Drummond with Myford stand...

Lathe: Myford / Drummond with Myford stand, Pre ML7 Myford lathe with selection of change wheels, 3 jaw and 4 jaw chucks, face plate and other attachments.On Myford stand, itself alone worth £350.A good solid machine, ideal for serious engineers and previously owned by a respected craftsman.Currently in storage and needs a new home soon as the space is required. Showing a little surface rust that doesn't affect the integrity and quality of the machine.Please give me a call or an email to arrange a viewing.Advertised on other sites. Serious offers considered. £, Bournemouth,.

Myford ml7 lathe + Myford stand...

Myford ml7 lathe + Myford stand, Myford ml7 lathe + Myford stand comes with forward and reverse switch + oiler lathe in good condition and working order. £, Brighton, .

Myford Super 7B Lathe for Sale

Myford Super 7 B 3 1/2" x 19" with Myford Stand, fitted screw cutting gearbox & Metric Conversion set in original box. Power Cross Feed. Digital Read Out and Inverter Speed Control (single phase). Myford Dickson Quick Change tool holder with 5 extra holders. 4" 3 jaw self-centring chuck, 6" 4 jaw independent chuck, Faceplate, Carchplate, spare backplate, Keyless 2MT Drill Chuck, Long Cross-slide with Rear Parting Toolpost, oilgun. Excellent condition throughout. Telephone ... (click to reveal full phone number)

METRIC CONVERSION SET for MYFORD SUPER 7B LATHE

One full set of the correct gearwheels (12) plus quadrant, spacers & spindles, for use with Super 7B (gearbox) lathes. All items are in good condition. There is also a revised copy of the Myford gearing chart. The new price is now £290. My price, (a saving of £95) includes carriage to UK mainland. Remote areas £5 extra, Read More

TWO Chucks Suitable for Myford Series 7 Lathes.

I have TWO British chucks for sale, both needing a polish, but in good useable condition, as follows:. 1) 6" Crown 4-jaw chuck with Myford backplate and key. £" Pratt-Burnerd 4-jaw chuck with Myford backplate, no key. £80.. I also have several smaller chucks. Please ask if interested.. A £10 reduction has been made for each missing chuck key.. Three pictures are shown for each chuck. If you cannot collect in person I will give you an exact carriage price, and my promise to keep this to the bare minimum. Read More

THREE Chucks Suitable for Myford Series 7 Lathes.

I have for sale three chucks, (two British and one foreign) for sale, all in good clean condition, as follows:. 1) 5" Pratt-Burnerd 4-jaw chuck with Myford backplate, No key. £" Crown 4-jaw chuck with Myford backplate and key. £" Indian make 3-jaw chuck unused, with all six jaws and key, but no backplate. £45.. I also have several smaller chucks. Please ask if interested.. Pictures are shown for each chuck in the above order. If you cannot collect in person I will give you an exact carriage price, and my promise to keep this to the bare minimum. Read More

FOUR Chucks Suitable for Myford Series 7 Lathes.

I have for sale four chucks, (three British and one Czech) for sale, all in good clean condition, as follows:. 1) 6" Crown 4-jaw chuck with Myford backplate & key. £" TOS 3-jaw chuck unused, with all six jaws & key, but no backplate. £" Pratt 3-jaw chuck with all six jaws,Myford backplate & key. £" Pratt 3-jaw chuck with all six jaws and key. £55.. I also have several other 3" and 4" 3-jaw chucks without backplates, and several sets of Pratt jaws. Please ask if interested.. Pictures are shown for each chuck in the above order, followed by the spare scroll chuck jaws. Details on request. If you cannot collect in person I will give you an exact carriage price, and my promise to keep this to the bare minimum. Read More

WANTED, 3-PHASE MOTOR for MYFORD series 7 lathe.

I am looking for a 3-phase resiliently-mounted motor to suit my Myford Super 7. Must be dual voltage -phase 3/4 to 1-h.p. motor in good working condition. I have an excellent single phase (230 volt) Motor 550 watts (2/3 h.p.) to suit a Myford lathe. See photos. Made by EMAC of Scotland. Complete with capacitor & shaft key. Good clean condition, tests OK. With good resilient mounting rings to fit your existing motor cradle. I will sell it for £70 or consider a comparable part-exchange. Read More

British 3-jaw Chuck Suitable for Myford Series 7 Lathes.

One- 4.25" Pratt 3-jaw chuck with all six jaws and key. Post free to UK mainland. Read More

New & Unused 230 volt motor for MYFORD Series 7 lathe

I have for sale a new 230 volt, 550 watts (3/4 h.p.) rpm resiliently-mounted motor bought (in error) for my lathe rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Runs almost silently. Price includes carriage to all except remote areas, for which I can quote the extra price on receipt of your postcode. I also want a sound 230-volt Myford compatible coolant pump priced at around £50. Read More

SAVE £50. New 230 volt motor for MYFORD Series 7 lathe.

I have for sale a new 230 volt, 550 watts (3/4 h.p.) rpm resiliently-mounted motor bought (in error) for my lathe rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Runs almost silently. My price includes carriage to all except remote areas, for which I can quote the extra price on receipt of your postcode.. I need a similar 3-phase motor for my lathe, which has an inverter drive, and would consider a part-exchange on the above or a direct swap if your motor 3-phase motor is in new condition.. I also need a sound 230-volt Myford compatible coolant pump with a stem length of 180 mm. priced at around £50. Read More

SAVE £50. New 230 volt motor for MYFORD Series 7 lathe.

I have for sale a new 230 volt, 550 watts (3/4 h.p.) rpm resiliently-mounted motor bought (in error) for my lathe rebuild. See photos. Complete with capacitor & shaft key. The shaft (still with its protective blue coating) is mm) x 2" (50 mm). Runs almost silently. My price includes carriage to all except remote areas, for which I can quote the extra price on receipt of your postcode.. I also want a sound 230-volt Myford compatible coolant pump with a stem length of 180 mm. priced at around £50. Read More

Contact

• Next →