jm corporation rokker fairing mount tweeter kit harley

J&M Corporation Rokker Fairing Mount Tweeter Kit- Harley

SKU: , This exciting new JM ROKKER XT series tweeter kit has been designed specifically for use on the Harley UltraClassic BatWing or RoadGlide style fairing.These are 25mm diameter highoutput dome tweeters designed to bring extra highfrequency definition to your Harley Bagger audio system.These tweeters are exact dimensional,wire connection substitutes for Harley part A.Tweeters are specd at 2 ohms nominal impedance,and will work with any radio or amplifier designed to operate at a 2,4,6 or 8ohm load.Rated at 300w peak power 150w RMS,khz frequency range, 94db sensitivity,1w,1m,these tweeters can easily replace two of the stock Harley gauges on the inside fairing panel.These new JM ROKKER XT series tweeters will connect direct to the midrange output jack on the back of the JM ROKKER series speaker crossover network OR to the factory Harley wiring harness on certain CVO StreetGlide,RoadGlide fairings OR to the front speaker spade connections inside the fairing,using the custom made plugnplay wiring harnesses included.This kit includes 2 tweeters,alternate connection wire assemblies,along with all necessary mounting hardware,complete installation instructions.

J&M Corporation Rokker XX 7.25 Inch Fairing Speaker Kit -

SKU: drivers are the largest diameter speakers that can be installed into the Harley fairings217 watts maximum outputVery thin,waterproof injectionmolded polycarbonate driver coneSpeciallytuned speakermounted crossover network for connection of optional JM fairing or grillemounted tweeter and midrange drivers

J&M Corporation Rokker XX 6.65 Inch Fairing Speaker Kit-

SKU: , Specd at 2 ohms impedance 217 watts maximum input 156w RMS continuous,92db sensitivitySpeakers provide the ultimate in raw powerInclude the silkdome tweeter bridge as part of the designLightweight,waterproof,onepiece designSuper highdensity,lightweight Neodymium magnet structureVented voice coil and magnet structure improves cooling when operating at high volume levels for extended periodsCustom maxflow speaker grilles for clear sound at highway speeds

J&M Corporation Saddlebag Lids With JM Rokker Speakers-

SKU: , JMs new 7,round subs are the largest diameter speakers that can be installed into the Harley Bagger Saddlebag lids,with cone volume and mass comparable to a 6X9 speaker.This new threeway highperformance speakerlid set has been designed specifically for the Harley Bagger style saddlebags.Specd at 2 ohms impedance and 170 watts max power,these new speakers provide the ultimate raw audio power.Features of this new ROKKER series speaker kit from JM are: Waterproof injectionmolded polycarbonate woofer cone. Highflux strength but liteweight dualdonut Neodymium magnet. High efficiency VENTED voicecoil for improved cooling when operating at high volume levels for extended periods. Custom designed grillwork with highoutput titaniumcolored tweeter and midrange drivers.Saddlebag lids are finished in primer black color,ready for the custom color of your choice.Top quality hardware,custom plugnplay wiring harness and complete installation instructions are included.

J&M Corporation Fairing Speaker Accoustic Pad Kit- Harley FL

SKU: , JMs new infairing acoustic pads are one of the easiest things you can do to tightenupthebass and improve the overall sound quality of your fairing mounted speakers.These special acoustic foam pads are diecut with adhesive installed and are specd for the versions of the Harley Classic BatWing Fairing.Installation is a snap,kit includes complete and detailed installation instructions.This Product Is Compatible With These JM Product Families: Harley UltraStreetElectra Glides

J&M Corporation Rokker Saddlebag 7.25 Inch Speaker Kit-

SKU: , The MOST POWERFUL speaker available for your Harley Bagger audio system JMs NEW ROKKER XX series 7.25 drivers,are the largest diameter speakers that can be installed into the Harley Bagger style saddlebags,with cone volume and mass comparable to a 6X9 speaker.Specd at 2 ohms impedance and an impressive 217 watts maximum input 156w RMS continuous,92db sensitivity,these new speakers provide the ultimate in raw audio power.This complete custom speaker installation kit with lids included,has been designed specifically for the Harley Bagger saddlebags.Features of this new ROKKER XX series speakerlid kit from JM are:Very thin,waterproof injectionmolded polycarbonate driver cone.Super highdensity liteweight Neodymium magnet structure,specially coated to maintain fluxstrength integrity even at extreme operating temperatures.High efficiency VENTED voicecoil,magnet structure for improved cooling when operating at high volume levels for extended periods.Speciallytuned speakermounted crossover network for connection of optional JM tweeter and midrange drivers.Saddlebag lids are finished in primer black color,ready for the custom color of your choice.Top quality hardware,custom plugnplay wiring harness and complete installation instructions are included.These are THE most powerful speakers you can buy for your Harley and they will perform extremely well when used with a medium to highpowered accessory amplifier. Buy Now

Hawg Wired Dash Tweeter Kit Matte Black- Harley Davidson

SKU: , Our new standard tweeter kits are exactly what your bikes audio system and your ears have been asking for. Each tweeter kit consists of two modules that fit in the two small recesses of your inner fairing under your windshield and follows the Batwing fairings natural lines perfectly. Rated at 50 watts RMS per tweeter,each module includes crossovers and a plug and play harnesses that makes installation a snap. Available in two finishes,matte to match the stock fairing can be painted and gloss black.Key FeaturesPlug and play connectionsAvailable in two finishesFits FLHT style fairings100 weather resistantPrecision molding offers perfect fitKit Includes2,Tweeter Modules2,Crossovers Modules1,Installation Hardware Kit1,Installation TemplatesSpecifications:3rd order 18 dboctave Crossover50 Watts RMS,100 Watts Peak Rated,50 WattsSensitivity,SPL: 93dB 2dB,1W,1MNeodymium magnet,28mm x 8.5mm Buy Now

Ciro 3D Fairing Ball Mount Black for Ciro Holders- Harley

SKU: , The Ciro Fairing mount keeps your device,drink,or camera front and center. This mount works great with any Ciro ball mount accessories and really helps keep your eyes on the road.Mounts Ciro accessories at the top of your fairing to help keep your eyes on the road.Very handy for use with mobile based GPS.Can be used to mount Ciro device holders,cupdrink holders,cameras,and more. Patent Pending

J&M Corporation Rokker Audio XT Dual 7.25 Inch 2 ohm

SKU: , JMs ROKKER XT series,Blow away those overlyheavy,inefficient bracketbreakin 6.5s,,JMs NEW ROKKER XT series 7,round subwoofers are large diameter dedicated lowfrequency speakers,with cone volume and mass comparable to a 6X9 speaker.Specd at 2 ohms impedance,403khz frequency response and 200 watts max power,these new JM subs provide the ultimate in bass response,lowfrequency audio power.This custom kit allows these new JM subwoofers to be mounted down into the rear portion of the stock Harley saddlebags,while leaving more than 75 of the saddlebag storage area available for normal luggage.Features of this new JM ROKKER XT series dualsubwoofer kit are: Waterproof mylarpolycarbonate woofer cone. Highflux strength but liteweight dualdonut Neodymium magnet. High efficiency VENTED voicecoil for improved cooling when operating at high volume levels for extended periods. Custom designed grillwork for mounting in the rear saddlebag position,with mounting spacers,weatherproof gasket seals,protective rear luggage cowl. These new JM ROKKER XT series subwoofers are designed to be connected to the rear channels of our 500w 4channel ROKKER amplifier,which is then switched into LOWFREQ mode,with proper crossover frequency,gain adjustments. You wont be disappointed.

J&M Corporation Z-Series Lower-section 8-pin Cord JM Corp

SKU: , This heavyduty ZSeries 8pin lowersection hookup cord is to be used with all JM Elite Series headset s HSECD629,HSICD629,HSECD584,HSICD584,HSECD477,HSICD477,HSECD374,HSECD271 and HSECD269 headsets for connection to,JM Corp,BMW 6pin audio systems 99 and newer.

Gardner-Westcott Engine Mount Custom Hardware Kit - Harley

SKU: , Fits: Harley DavidsonFX Dyna Softail FXST Top,front and rear bolts for engine mount.

Kuryakyn Inner Fairing Covers - Harley Davidson Electra

SKU: , Is your inner fairing dull or sunfaded in this area Heres an instant fix to make this area even better than new PeelStick

Kuryakyn Bat Brow Fairing Trim - Harley Davidson

SKU: , Bring your batwing fairing to life with the Bat Brow. The brilliant chrome finish goes with any color and adds an individualized edge to really show off your ride. Installation is easy,just clean,peel,then stick and enjoy. Looks great with our Bat Lashes

Drag Specialties Lower Fairing Support Bar Black- Harley

SKU: , Mounting bar replaces the OEM lower fairing brackets when eliminating the engine guardhighway bar from FLTR modelsEasy to installIncludes mounting hardwareMade in the U.S.A.NOTE: Not for use with OEM turn signals and mounts Buy Now

Lindby Custom Fairing Support Bar Chrome - Harley Davidson

SKU: , Eliminates the need for the OEM highway bar. Uses all stock brackets for an easy and clean installation. Buy Now

Kuryakyn Tri-Line Fairing Accents Chrome Pair- Harley

SKU: , Sleek and streamlined with a brilliant chrome finish,these accents are sure to add distinctive style to your outer fairing. Designed to complement the traditional bat wing shape with their unique TriLine feature. Easy peelandstick installation.Shown on bike with additional Kryakyn accessories. Sold separately

Kuryakyn Fairing Vent Accent Chrome- Harley Davidson Electra

SKU: , This awesome looking and highly noticeable fairing vent accent will transform the look of your standard and newer Harley Davidson Electra Glide,Street Glide or TriGlide from plain to spectacular at a super affordable price.A clean and simple solution to update the look of the boring black vent on the new Electra Glide,Street Glide,Trike fairing.Shown on bike with additional Kryakyn accessories. Sold separately

Kuryakyn Lighted Bat Lashes For Batwing Fairing - Harley

SKU: , Its no secret,most top designers in any field would concur. The keys to good looks are keeping it simple,highlighting the contours. Regardless of the color or finish,chrome goes with anything,these Lighted Bat Lashes will add depth,character to the timehonored Batwing Fairing. Bat Lashes require no tools,no drilling. Simply clean the surface,peel,stick,admire Lighted Bat Lashes are also surface mount but do require drilling to route wiring. Buy Now

Russ Wernimont Designs Cafe Long Fairing- Harley Davidson

SKU: , Provides traditional style with flairDiverts air around the driverShort style fairing measures inches highLong style fairing measures inches highMounting hardware includedMade in the U.S.A. Buy Now

LA Choppers Fairing Mirror Removal Plug Black- Harley

SKU: , The perfect plug for covering the unsightly hole left behind in your fairing when relocating the stock mirrorsSeamlessly blends with your stock fairing looking like your bike was meant to come that way yet still adds a minor flare to an otherwise dull spotAvailable in chrome as a more showy accent piece,or black to blend in more with your fairingFits: HarleyDavidson Touring

Kuryakyn Inner Fairing Cover Plates Pair - Black - Harley

SKU: , The old catch 22. Youve removed the stock mirrors from your Street Glide in favor of more unique,stylized mirrors,but now the stock mounting holes are still there,staring you right in the face Inner Fairing Cover Plates replace any trace of the stock mirrors with cool accents styled to blend right in. High strength peel,stick adhesive makes installation a snap. Buy Now

Klock Werks Fairing Vent Screen Round Holes- Harley Davidson

SKU: , Klock Werks has created a simple yet effective part to accent the vent in the new Harley Davidson FL batwing style fairing. Available in Honeycomb or Round pattern mesh aluminum,the Klock Werks Fairing Vent Screen is easy to install,and adds a custom touch to the front of your fairing. The Vent Screen may even catch or stop larger bugs and other road debris from entering through your fairing ventAccent the vent in the new HD vented fairing with Klock Werks Fairing Vent ScreenAvailable in Honeycomb and Round pattern mesh aluminumMade in the U.S.A.Vent screen may even catch or stop larger bugs and other road debris from entering through your fairing ventFairing Vent Screen is easytoinstall,and adds a custom touch to the front of your fairingInstallation instructions and mounting adhesive includedEasy installationMade in the USA

Kuryakyn Run Turn Edge Accents for Batwing Fairing - Harley

SKU: , A nice subtle touch of chrome,additional lighting to create a unique look. Perfectly contoured to follow the lines of the outer edge on the inner fairing,the addition of auxiliary run,turn lighting make this a must have. Installation requires no drilling or modification to the fairing.

Kuryakyn Fairing Lower Speakers 4 Ohm - Harley Davidson FL

SKU: , Make good use of those fairing lowers by adding the best speakers around Kicker KPS ohm Speakers mounted in gloss black housings wrapped in Kryakyn Chrome,The ultimate blend of amazing sound,great looks Speakers are angled towards the rider for optimum sound quality,will accept any of our Speaker Grills. Kicker Amplifier,Wiring Harness Part KY871 required for installation sold separately. Buy Now

J&M Corporation FLEXPOWER CB Antenna Harley Davidson Classic

SKU: , JMs new FLEXPOWER hideaway CB antenna is THE BEST hideaway CB antenna on the market today,to help you eliminate altogether the rear mounted CB antenna on your Harley.This JM infairing CB antenna is pretuned from our factory for the 27mhz CB radio band no further tuning is required during installation and is specd for the and newer versions of the Harley Classic BatWing or RoadGlide Fairing,with JM or other aftermarket style CB radio,using the PL259 antenna connector.Installation is a snap,as there are no wires to cut or splice and antenna wire lead is secured in the fairing with included double sided tape clips.Antenna kit includes complete and detailed installation instructions.

Contact

• Next →