3 electrocube w250b022uf 200v polyester

  3 Electrocube W250B.022uf 200V Polyester

Here are three (only two pictured) new old stock Electrocube W250B Polyester (Mylar) film and foil capacitors.022uf at 200V +/- 5% tolerance 5/8" long with 2.5" axial leads The longer wires are good for central grounding points.  These are great for humbucker or single coil equipped guitars.  This is the quickest and easiest mod you can make to your guitar.  Just replace the original tone caps with these.  Even if you don't use your tone control, you'll hear a difference.   These are an excellent direct replacement upgrade for guitars with humbuckers I like these poly film caps.  I've installed them in numerous guitars. They all read within tolerance on a Triplett Capacitance Meter Free shipping in the USA Worldwide USPS First Class International shipping Check our other listings

  3 Electrocube 250B.022uf 200V Mylar / Foil

Here are three (only two pictured) new old stock Electrocube W250B Polyester (Mylar) and foil capacitors.022uf at 200V +/- 5% tolerance 5/8" long with 2.5" axial leads The longer wires are good for central grounding points.  These are great for humbucker or single coil equipped guitars.  This is the quickest and easiest mod you can make to your guitar.  Just replace the original tone caps with these.  Even if you don't use your tone control, you'll hear a difference.   These are an excellent direct replacement upgrade for guitars with humbuckers I like the sound, smoothness, and low noise of these poly film caps.  The higher voltage ones are also used in high end guitar amps. Free shipping in the USA Worldwide USPS First Class International shipping Check our other listings

  3 ELPAC ZD2A.012uf 200V Polyester

Here are three (only two pictured) new old stock  ELPAC metallized polyester (mylar)  capacitors ZD2A.012uf 200VDC +/-10% tolerance 3/8" long with 2 3/8" axial leads These are highly sought after for guitars, speaker circuits, tube or solid state amplifiers, or for any application that requires high end caps. Great for the neck pickup of humbucker equipped guitars G reat for any electronic project - pedals, crossovers, amps, guitar or bass. Free shipping in the USA Worldwide USPS First Class International shipping C heck our other listings

  3 Genuine Sprague 192P.039uf 200V Mylar /

Here are three (only two pictured) new old stock  Sprague 192P  Mylar film / foil capacitors.039uf  200V 5/8" long with 1.50" axial leads Black poly sleeved, epoxy sealed ends These are great for humbucker or single coil equipped guitars.  These have the same composition as Sprague 225P Orange Drop caps without the epoxy coating and radial leads. The.039 caps are great for a brighter sound from guitars normally equipped with.047 caps and to smooth and slightly darken guitars with.022 caps.  The higher the uf number, the more highs are sent to ground.  These caps are a great change and one of the simplest mods you can make to your guitar.  Just replace the existing tone capacitor attached to your tone control with these. I like the sound, smoothness, and low noise of these Sprague Mil-Spec caps and I've put these in numerous guitars.  The higher voltage ones are also used in high end guitar amps. Free shipping in the USA Worldwide USPS First Class International shipping Check our other listings

  3 Electrocube 230B.022uf 50V Metallized

Here are three (only two pictured) new old stock Electrocube W230B Metallized Polyester capacitors.022uf  50V +/- 5% tolerance 1/2" long with 2.5" axial leads The longer wires are good for central grounding points.  These are great for humbucker or single coil equipped guitars. This is the quickest and easiest mod you can make to your guitar.  Just replace the original tone caps with these.  Even if you don't use your tone control, you'll hear a difference.   These are an excellent direct replacement upgrade for guitars with humbuckers I like the sound, smoothness, and low noise of these poly film caps.  The higher voltage ones are also used in high end guitar amps. Free shipping in the USA USPS First Class International shipping Check our other listings

  3 Electrocube 230B.022uf 50V Poly Film

Here are three (only two pictured) new old stock Electrocube W230B Metallized Polyester film capacitors.022uf  50V +/- 5% tolerance 1/2" long with 2.5" axial leads The longer wires are good for central grounding points.  These are great for humbucker or single coil equipped guitars. This is the quickest and easiest mod you can make to your guitar.  Just replace the original tone caps with these.  Even if you don't use your tone control, you'll hear a difference.   These are an excellent direct replacement upgrade for guitars with humbuckers I like the sound, smoothness, and low noise of these poly film caps.  The higher voltage ones are also used in high end guitar amps. Free shipping in the USA USPS First Class International shipping Check our other listings

Distinctive UK Made Polyester Black Wide Fit Polyester Tie

Description: High Quality Distinctive UK Made Branded Polyester Men's Wide Fit Tie Read more

Summer weight duvet - Polyester and 2 Polyester pillows in

Summer weight duvet - Polyester and 2 Polyester pillows Duvet only used for display on a guest bed (in a duvet cover) £ Duvet and Pillows together Collection only - Basingstoke

Premium grade polyester filling/stuffing and polyester wadding

Premium grade polyester filling, craft toy,, teddy bear, pillows, stuffing. 800gr. Fire retardant. Also polyester wadding. Ideal for crafts, quilting... 5£ all Ad ID: Delivery Service Consumer Credit

Marks Spencer 70 s Polyester Brown Wide Fit Polyester Tie

Description: High Quality Marsk Spencer 70 s Branded Polyester Men's Wide Fit Tie Read more

OPEN 12"x 18" Polyester Super Polyester 2 Sided Garden Flag

OPEN 12

BNIB Crosswater Mike Pro 200V Shower Head 200mm Brushed

BNIB Crosswater Mike Pro Stainless Steel Shower Head 200mm Excellent quality shower rose PRO 200V BRUSHED STAINLESS STEEL 200mm Fixed Head http://www.crosswater-mikepro.co.uk/product/shower-heads/fixed-head-/ Cancollect from either Colchester, Essex or IP14 4LE

  POLYESTER ROPE - 14mm polyester leadline

you are bidding on/buying a 20 metre length of 14mm polyester leadline (lead weighted) rope. our polyester leadline rope is EXTREMELY strong and durable and is very reliable. leadline rope is mainly used for fishing/mooring/anchoring etc...but because of its ultra strength, can also be used for other purposes, such as yachting and even towing etc.... this rope has an ultra thin polyethelene outer shell for visibility purposes, which is very easily removed if required.

  2 Electrocube Guitar Treble Bleed Bypass

Two new old stock NOS Electrocube 230D metallized polyester capacitors and two 220k resistors.001uf (pf) 600V +/-5% tolerance The caps measure 3/8" long with 1" axial leads This kit is for passive electric guitars.   Many times when you turn the volume down using your guitar’s volume pot, a lot of the high frequency is lost.   This simple “fix” will help your guitar sound the same no matter what setting your volume control is at.   By placing a small capacitor between the input and output of the volume control, you allow the high frequencies to bleed through to the output.   The resistor smoothes out the pot’s taper and the cap lets the highs escape the pot’s resistance when you turn down the volume pot. This kit contains two  metallized polyester  capacitors which I’ve found have a great sound.   This kit has detailed, easy to understand directions for installation, with pictures and diagrams.   The capacitors and resistors can be pre-soldered in parallel.  This will save you time and effort.  Or I can send them as separate components and you can choose how to install them.  Some people like them in series or the capacitor alone.  It's your choice. You get two new old stock.001uf Electrocube 230D capacitors and two 220k resistors.  This kit can be used with humbuckers or single coil setups.  Some manufacturers of pickups have suggested using from.001uf / pf to.uf / pf caps for the treble bleed circuit.  Others have suggested from a 220pf to a 750pf.   Only you know what you want your guitar to sound like.  All components are brand new.  This is an easy mod.  All you need is a soldering iron and access to the back of your volume control pot. Free Shipping in the USA Worldwide USPS First Class International shipping Check our other listings  

  2 Electrocube Guitar Treble Bleed Bypass

Two new old stock NOS Electrocube 230D metallized polyester capacitors and two 150k resistors.001uf (pf) 600V +/-5% tolerance The caps measure 3/8" long with 1" axial leads This kit is for passive electric guitars.   Many times when you turn the volume down using your guitar’s volume pot, a lot of the high frequency is lost.   This simple “fix” will help your guitar sound the same no matter what setting your volume control is at.   By placing a small capacitor between the input and output of the volume control, you allow the high frequencies to bleed through to the output.   The resistor smoothes out the pot’s taper and the cap lets the highs escape the pot’s resistance when you turn down the volume pot. This kit contains two  metallized polyester  capacitors which I’ve found have a great sound.   This kit has detailed, easy to understand directions for installation, with pictures and diagrams.   The capacitors and resistors can be pre-soldered in parallel.  This will save you time and effort.  Or I can send them as separate components and you can choose how to install them.  Some people like them in series or the capacitor alone.  It's your choice. You get two new old stock.001uf Electrocube 230D capacitors and two 150k resistors.  This kit can be used with humbuckers or single coil setups.  Some manufacturers of pickups have suggested using from.001uf / pf to.uf / pf caps for the treble bleed circuit.  Others have suggested from a 220pf to a 750pf.   Only you know what you want your guitar to sound like.  All components are brand new.  This is an easy mod.  All you need is a soldering iron and access to the back of your volume control pot. Free Shipping in the USA Worldwide USPS First Class International shipping Check our other listings  

  2 Electrocube 250B Guitar Treble Bleed

Two NOS Electrocube 250B polyester and foil capacitors and two 150k resistors pre-soldered in parallel.uf (pf) 200VDC +/-5% tolerance The caps measure 7/16" long with 2 1/8" axial leads This kit is for passive electric guitars.   Many times when you turn the volume down using your guitar’s volume pot, a lot of the high frequency is lost.   This simple “fix” will help your guitar sound the same no matter what setting your volume control is at.   By placing a small capacitor between the input and output of the volume control, you allow the high frequencies to bleed through to the output.   The resistor smoothes out the pot’s taper and the cap lets the highs escape the pot’s resistance when you turn down the volume pot. This kit contains two polyester (mylar) and foil capacitors which I’ve found have a great sound   This kit has detailed, easy to understand directions for installation, with pictures and diagrams.   You get two new old stock.uf Electrocube 250B capacitors and two 150k resistors soldered in parallel.   This kit can be used with humbuckers or single coil setups.  Some manufacturers of pickups have suggested using from.001uf / pf to.uf / pf caps for the treble bleed circuit.  Others have suggested from a 220pf to a 750pf.   Only you know what you want your guitar to sound like.  All components are brand new.  This is an easy mod.  All you need is a soldering iron and access to the back of your volume control pot. Free Shipping in the USA Worldwide USPS First Class International shipping Check our other listings  

  2 Electrocube 250B Guitar Treble Bleed

Two new old stock NOS Electrocube 250B mylar and foil capacitors and two 150k resistors.001uf (pf) 200V +/- 5% tolerance The caps measure 1/2" long with 2.5" axial leads This kit is for passive electric guitars.   Many times when you turn the volume down using your guitar’s volume pot, a lot of the high frequency is lost.   This simple “fix” will help your guitar sound the same no matter what setting your volume control is at.   By placing a small capacitor between the input and output of the volume control, you allow the high frequencies to bleed through to the output.   The resistor smoothes out the pot’s taper and the cap lets the highs escape the pot’s resistance when you turn down the volume pot. This kit contains two  mylar and foil capacitors which I’ve found have a great sound.   This kit has detailed, easy to understand directions for installation, with pictures and diagrams.   I can send the components and you can solder the components together before installation, or, I can solder them together for you.   Your choice, you just have to let me know.  Some people just want to use the capacitor by itself.  Some want to wire them in series.  I like the components wired in parallel. You get two new old stock.001uf Electrocube 250B capacitors and two 150k resistors.  This kit can be used with humbuckers or single coil setups.  Some manufacturers of pickups have suggested using from.001uf / pf to.uf / pf caps for the treble bleed circuit.  Others have suggested from a 220pf to a 750pf.   Only you know what you want your guitar to sound like.  All components are brand new.  This is an easy mod.  All you need is a soldering iron and access to the back of your volume control pot. Free Shipping in the USA Worldwide USPS First Class International shipping Check our other listings  

  2 Electrocube 250B Guitar Treble Bleed

Two NOS Electrocube 250B polyester and foil capacitors and two 150k resistors.uf (pf) 200VDC +/- 5% tolerance The caps measure 7/16" long with 2 1/8" axial leads This kit is for passive electric guitars.   Many times when you turn the volume down using your guitar’s volume pot, a lot of the high frequency is lost.   This simple “fix” will help your guitar sound the same no matter what setting your volume control is at.   By placing a small capacitor between the input and output of the volume control, you allow the high frequencies to bleed through to the output.   The resistor smoothes out the pot’s taper and the cap lets the highs escape the pot’s resistance when you turn down the volume pot. This kit contains two polyester (mylar) and foil capacitors which I’ve found have a great sound   This kit has detailed, easy to understand directions for installation, with pictures and diagrams.   I can send the components and you can solder the components together before installation, or, I can solder them together for you.   Your choice, you just have to let me know.  Some people just want to use the capacitor by itself.  Some want to wire them in series.  I like the components wired in parallel. You get two new old stock.uf Electrocube 250B capacitors and two 150k resistors.  This kit can be used with humbuckers or single coil setups.  Some manufacturers of pickups have suggested using from.001uf / pf to.uf / pf caps for the treble bleed circuit.  Others have suggested from a 220pf to a 750pf.   Only you know what you want your guitar to sound like.  All components are brand new.  This is an easy mod.  All you need is a soldering iron and access to the back of your volume control pot. Free Shipping in the USA Worldwide USPS First Class International shipping Check our other listings  

  3 Nytronics uf 100VDC Polyester Film

Here are three (only two pictured) new old stock  Nytronics 107  Polyester (mylar) film capacitors.022uf at 100 volts +/-10% tolerance " long with 1 7/8" axial leads The longer wires are good for central grounding points.  These work great for single coil or humbucker equipped guitars.  These are high end audiophile coupling/tone/bypass caps, good for almost any audio application. These are a direct replacement upgrade for humbucker equipped guitars I like the sound, smoothness, and low noise of poly film caps and I've put them in numerous guitars.  The higher voltage ones are also used in high end guitar amps. Free shipping in the USA Worldwide USPS First Class International shipping Check our other listings

3 X 5 Polyester Patriotic Flags

Change country: -Select- Australia Austria Bahrain Belgium Brazil Bulgaria Canada China Croatia, Republic of Cyprus Czech Republic Denmark Estonia Finland France Germany Greece Hong Kong Hungary Indonesia Ireland Israel Italy Japan Korea, South Kuwait Latvia Lithuania Malaysia Malta Mexico Netherlands New Zealand Norway Philippines Poland Portugal Qatar Romania Saudi Arabia Singapore Slovakia Slovenia South Africa Spain Sweden Switzerland Taiwan Thailand Ukraine United Arab Emirates United Kingdom United States There are 1 items available. Please enter a number less than or equal to 1. Select a valid country. Postcode: Please enter a valid postcode. Please enter up to 7 characters for the postcode

  3 Matsushita.047uf 100V Polyester Film

Here are three new old stock NOS Matsushita Polyester film tone capacitors.047uf  100V +/-" long with 2" axial leads These are great for humbucker or single coil equipped guitars.  There are two for guitars with two tone controls, or, for more than one guitar with only one tone control. These caps are a great change and one of the simplest mods you can make to your guitar.  Just replace the existing tone capacitor attached to your tone control with these. They all read well within 10% on a Triplett Capacitance Meter This is an exact replacement upgrade for single coil guitars I like the sound, smoothness, and low noise of these Made in Japan film caps and they work great in single coil guitars.   These are dated November and their code number is CP474SB3. Free USPS Shipping in the USA Worldwide USPS First Class International shipping Check our other listings

  3 Nytronics 133A.047uf 50VDC Polyester

Here are three (only two pictured) new old stock  Nytronics 133A  Polyester (mylar) and foil capacitors.047uf 50VDC +/-5% tolerance 3/4" long with 2.5" axial leads date code All read well within tolerance on a Triplett Capacitance Meter   The longer wires are good for central grounding points  These work great for single coil or humbucker equipped guitars  These are high end coupling caps, good for almost any electronic application These are a direct replacement upgrade for single coil equipped guitars - Strats and Teles I like the sound, smoothness, and low noise of poly film caps and I've put them in numerous guitars.  The higher voltage ones are also used in high end guitar amps. Free shipping in the USA Worldwide USPS First Class International shipping Check our other listings

  3 IMB.039uf 50V Polyester Foil Film

Here are three (only two pictured) new old stock IMB Polyester and foil/film guitar tone capacitors.039uf at 50 volts +/- 10% Tolerance 3/8" long with 2" axial leads The longer wires are good for central grounding points.  These work great in single coil equipped guitars, or guitars with humbuckers.  The lower the uf number, the more highs are let through. These are a great replacement upgrade for single coil equipped guitars I like the sound, smoothness, and low noise of poly film caps and I've put these in dozens of guitars.  The higher voltage ones are also used in high end guitar amps. Check our other listings

  3 Nytronics 107B.039uf 100V Polyester Film

Here are three (only two pictured) new old stock  Nytronics 107B  Polyester (mylar) film capacitors.039uf  100V +/-1% tolerance " long with 1 7/8" axial leads The longer wires are good for central grounding points.  These work great for single coil or humbucker equipped guitars.  These are high end audiophile coupling/tone/bypass caps, good for almost any audio application..039uf is a great Secret Tone and will slightly brighten single coil guitars I like the sound, smoothness, and low noise of poly film caps and I've put them in numerous guitars.  The higher voltage ones are also used in high end guitar amps. Free shipping in the USA Worldwide USPS First Class International shipping Check our other listings

Safavieh Handmade Precious Charcoal Polyester/ Wool Rug (3'

Safavieh's Precious collection is inspired by timeless designs crafted with the softest polyester and wool available. This rug is crafted using a hand-tufted construction with a pile and features main accent color of charcoal. A wool pile with special polyester accents gives this rug a glamorous look and feel with gorgeous gem tones. Durable cotton canvas backingPrimary materials: Polyester/ WoolLatex: YesPile height: 0.5 inchesStyle: ContemporaryP

Contact

• Next →